SHENZHEN CHAOYI MACHINE CO.,LTD

A . The link of motive force ；
1．The customers need compressor of air off a complete set before operate,(>/4 KW)，plastic of the precision and a tool of supplying.

2.The barometric pressure of the standard is 0.63Mpa，the tallest is0.7Mpa，least is 0.55Mpa，must be full for the equipment of the supplying.

3. The gas must filter and dry before the use .or it will be block, etch, and harmed of the machine, damaged of the motor.

4. We suggest that to use the oil-water separator (it was offered to customer as free accessory)


5.Check up the oil of supply, pull down the exhaust pipes, put a piece of paper near the  machine ,activate the motor ,if have a little oil on the paper ,so it is normal of supply, the long of windpipe can not surpass the 5metre, for the oil of supply with motor.，

Ｂ． Clear the waste paper of preparation
Put the paper with together in good order, the 4 sides must have cut
off the knife, made the waste side with product together.
Indicate specially ：
Put the paper better, not only efficiency can go up, but also can lower
of damage the rate.

Ｃ．Operate the steps (if you don't know how to operate it, please contacct us directly to get the instruction video)

1. The left hand clenched and ensue the hand and not to become
flexible, right hand relaxed, grasp with care of motor.
2.The right force more big ,the speed more high too, the speed treat,
and so start.
3. Put the chain with work on the waste side, the left hand keep
machine not move, the same time, to go to with force, the waste side
will down.
4. Over the work, the right hand uncover the switch, at the same time,
the motor will stop revolving.
5. First cut open the power source, second cut off the switch, before
stop using until the air finished, put the machine on the shelf for
safety.



Notice！
１.First clear two sides ,second clear behind ,the end clear front,
 this our suggestion.
２.If some sides very difficulty , please turn seat and go on.
３.The machine do not touch the foundation of paper , for safeguard
chain .

D．Removal of trouble and care and maintenance
（一）Every day wipe some oil after used , it is longer for carrying on.
（二）Stuff the paper and do it ：cut off air road is very important,
if the chain not work ,look at machine and open the left lid, take
out the paper, activate again and go on .
（三）Must check up  tension of chain often ,and adjust tension in
necessary ，after, the longest with distance of hang down is 1-2mm ，
it is right ,or will be collide each other .

Special notice ：
On every succeeding activity, fist cut off air road, and must release the air of remain, or cause the hurt for people easily. When the machine worked, not touch the part of turn, or arouse the hard hurt for worker.



Ｅ.Change the chain (if you don't know how to operate it, please contacct us directly to get the instruction video)
１.The chain of dismantle
Dismantle the two screws on the up side with cover safety, and dismantle the hand of lubricate, carry the guide of chain.

２.Set up the chain (if you don't know how to operate it, please contacct us directly to get the instruction video)
Put the chain on seat with right in the cover safety, all parts reset with the same of state after, connect the motor and strain the chain.


Ｆ．Others take care of work. (if you don't know how to operate it, please contacct us directly to get the instruction video)
１.Every two months check up machine and take care of tools ,clear ,wipe the oil ,the motor need to check up in working every two week.

２.According to the difference with uses the situation ,clean up at regular intervals and wipe the oil .

３.Do not place and don't the waste stripper a longer time ,or rust .

Any questions, please feel free to contact us:

Email: [email protected]
WhatsApp: +86 18475613114
Website: www.szchaoyimachine.com